A few things I would like to check...

[QUOTE=Joe Bleasdale;36412]
Firsty, IPCB.
I can think of a few instances where I want an IPCB fader for position parameters only. I will have this on the pages I need it. Now if I have my 2 positions on either end of the fader, but the same fixtures in an active cue.. when I move the fader will they automatically be altered by the fader? The when I am done with the fader and I press "go" again, the parameters will be taken control of by the main list..? I assume this is basic LTP stuff, but I want to check.


Make a Scene with just the position info. Make it IPCB and you'll be good to go. I have some Scenes for "blinders" where all of my movers move to either the "HOUSE" or "ROOF" position. I grab the handle and move it up and they go....when I bring the fader back down, they move back to where they were.

[QUOTE=Joe Bleasdale;36412]
Tap sync.
I know tap sync is requested for syncing items from the directory, and I am sure it is a high priority. My current idea of a way around this is to temporarily move the chase to a free master, tap sync it and then move it back. My question is, can this be done? Will the chase remember the beat even if it is deleted or moved from a master?


Yes, it remembers it's "last" BPM.

[QUOTE=Joe Bleasdale;36412]
Delay on a comment Macro.
I wish to put a delay time on a macro. I want the cue to fire, then 5 seconds later have the macro fire. I know I could put a time on the scene or cuelist I want to fire to do the delay, but I just wondered whether it was possible or even requested..?


Make a blank cue in your cue stack and make THAT cue your comment macro. I do this regularly where I want to do the move, change the master and then release all other lists.

Cue 1 - Cue info... CM2
Cue 1.1 - Wait of 5 ....blank info... RO


[QUOTE=Joe Bleasdale;36412]
I hope I make sense here...

No...doesn't make sense at all....:poke::poke::poke:
All perfectly excellent questions....

[QUOTE=Joe Bleasdale;36412]
Firsty, IPCB.
I can think of a few instances where I want an IPCB fader for position parameters only. I will have this on the pages I need it. Now if I have my 2 positions on either end of the fader, but the same fixtures in an active cue.. when I move the fader will they automatically be altered by the fader? The when I am done with the fader and I press "go" again, the parameters will be taken control of by the main list..? I assume this is basic LTP stuff, but I want to check.


Make a Scene with just the position info. Make it IPCB and you'll be good to go. I have some Scenes for "blinders" where all of my movers move to either the "HOUSE" or "ROOF" position. I grab the handle and move it up and they go....when I bring the fader back down, they move back to where they were.

[QUOTE=Joe Bleasdale;36412]
Tap sync.
I know tap sync is requested for syncing items from the directory, and I am sure it is a high priority. My current idea of a way around this is to temporarily move the chase to a free master, tap sync it and then move it back. My question is, can this be done? Will the chase remember the beat even if it is deleted or moved from a master?


Yes, it remembers it's "last" BPM.

[QUOTE=Joe Bleasdale;36412]
Delay on a comment Macro.
I wish to put a delay time on a macro. I want the cue to fire, then 5 seconds later have the macro fire. I know I could put a time on the scene or cuelist I want to fire to do the delay, but I just wondered whether it was possible or even requested..?


Make a blank cue in your cue stack and make THAT cue your comment macro. I do this regularly where I want to do the move, change the master and then release all other lists.

Cue 1 - Cue info... CM2
Cue 1.1 - Wait of 5 ....blank info... RO


[QUOTE=Joe Bleasdale;36412]
I hope I make sense here...

No...doesn't make sense at all....:poke::poke::poke:
All perfectly excellent questions....