• State Not Answered
  • +1 person also asked this people also asked this
  • Date
    ombrel - Former HES Forum Member
  • Date
  • Replies 8 replies
  • Subscribers 6 subscribers
  • Views 3086 views
  • Users 0 members are here

Trying to upgrade a Road Hog 3 fresh ISO install to v3.2.6

Hi,
I have two road hog 3 consoles with recently disks replaced to SDD's,
I've performed on both successful fresh full ISO restore (1.8.1 - ver. 3.2.1).
After a while I got back to them, to make upgrade to v3.2.6 (needed compatibility with h4 shows).
Unfortunately every attempt of running 3.2.6 msi file was returning:
"the selected software upgrade is not a valid whole hog software upgrade"
Yesterday I've managed to install "step by step", from v3.2.2 up to v3.2.4 and that's it.
Both files v3.2.5 and 3.2.6 are returning the same window:
"the selected software upgrade is not a valid whole hog software upgrade"
any thoughts?

Thanks in advance,
Chris
Parents
  • 0
    In Wholehog v3.2.6 Release Notes you can find:
    Installation Instructions
    "All Wholehog 3 generation consoles can be upgraded to v3.2.6 from any version of v3.2.X
    except the Wholehog 3 Console which should upgraded using the full restore if running v3.2.1
    or older.(...)"

    As I said, I've done already full ISO system restore and both consoles are working just fine.
    Moreover with SDD's they are fast and furious.
    My only concerns,
    I can not use the latest libraries available (they need v3.2.6)
    and I can not use old hog4 shows I was using on those roadhogs before change of the disks.
    What I have achieved so far:
    1 new SDD disk installed
    2 RoadHog System Restore image installed from the usb stick
    3 backup shows imported / only hog3 shows are working.
    4 I was trying to install v3.2.6 than 3.2.5 and 3.2.4 with no luck.
    5 I managed to install version after version v3.2.2 then 3.2.3 and 3.2.4 and thats it.
    both msi files (3.2.5 and 3.2.6) are returning the same error.

    Chris
Reply
  • 0
    In Wholehog v3.2.6 Release Notes you can find:
    Installation Instructions
    "All Wholehog 3 generation consoles can be upgraded to v3.2.6 from any version of v3.2.X
    except the Wholehog 3 Console which should upgraded using the full restore if running v3.2.1
    or older.(...)"

    As I said, I've done already full ISO system restore and both consoles are working just fine.
    Moreover with SDD's they are fast and furious.
    My only concerns,
    I can not use the latest libraries available (they need v3.2.6)
    and I can not use old hog4 shows I was using on those roadhogs before change of the disks.
    What I have achieved so far:
    1 new SDD disk installed
    2 RoadHog System Restore image installed from the usb stick
    3 backup shows imported / only hog3 shows are working.
    4 I was trying to install v3.2.6 than 3.2.5 and 3.2.4 with no luck.
    5 I managed to install version after version v3.2.2 then 3.2.3 and 3.2.4 and thats it.
    both msi files (3.2.5 and 3.2.6) are returning the same error.

    Chris
Children
No Data
Related

www.etcconnect.com