Radio Remote Focus Unit

Technically the RRFU will work with Congo, however the keys are layed out very differently.  It will not damage the desk in any way if you want to try it.  If you are going to experiment with the RRFU, I would suggest trying it with a new play file.

Functionally I would defiantly suggest investing in the CRRFU.  It will work much better for you.

Sincerely,

Benjamin Smith

Same question, but with a wired RFU...will it still work?

J. R. Lidgett
Salina Community Theatre

The Wired Expression RFU will not work with congo.

 The LCD Screen will display "Waiting for Communication" on the LCD Screen.

Congo Client Software, CRRFU (Congo Radio Remote Focus Unit), and the Phone remote is the only ETC Approved way of remotely controlling the Congo Console.

-Benjamin Smith

I noticed in the manual you are also able to use a Avab Lynx fader wing, which would at least give you a remote Go and master faders, which is what I usually need the RFU for.  My question is, can you even get these anymore, and if so, how long is the APN cable to connect to the console?

J. R. Lidgett
Salina Community Theatre

Hi there -

 Avab Lynx panels are not available in the US, and if they were they would only be compatible with the Congo console (which has the APN connector).

I would recommend looking into a MIDI fader board - Congo and Congo jr are controllable via MIDI input so you could customize one of these controllers to do pretty much anything you would like to do.

Thanks!

 
Sarah

 

Hi there,

I'm working with the congo v4.3 and we have the cRRFU remote. I was wondering where I can find out about using it with presets, groups, and other basic functions. I've looked in the manual and it says that instructions were packaged separately with the unit but I have been unable to find them. Any information would be much appreciated.

Also, do you still offer training for the congo?

Thanks!

-Lamont

Hello -

Here are the instructions from the Congo v5.1 online help system. Please note that At Mode operation is not supported in versions earlier than v5.1. Also, I believe that the separate remotes field did not get added until the v5.0 release, so interactions of the remote and the main console are shared, including recording. I highly recommend playing with your remote and your console for a bit to understand how they interact before doing a lot of remote work in v4.3 software. (Congo v4.3 is a quite old version - if it's possible I would recommend updating to the newest version - v5.1 - available for free download here.)

Thanks -

Sarah

cRRFU Operating Instructions

The transmitter has two available commands for each key on the unit.

Direct commands are displayed above each key. To access the commands that are displayed vertically to the left of each key, press the [FUNC] key first (do not press and hold [FUNC]).

An example of mixing direct and [FUNC] commands to record channels 1-5 at 75% into Preset 5 follows:

[1] [CHAN] [5] [THRU] [7][5] [@ LEVEL] [5] [FUNC] [RECORD]

[#] [CH]

[#] [THRU]
[#] [FUNC] [+]

[#] [FUNC] [-]

[#] [FUNC] [Group]

[FUNC] [All]

[FUNC] [100%]

[FUNC] [0%]

[#] [@Level]

[FUNC] [+%]

[FUNC] [-%]

[FUNC] [Check+]

[FUNC] [Check-]

[FUNC] [Go/Goto]

[FUNC] [Go Back]

[#] [FUNC] [Go/Goto]

[#] [FUNC] [Record]

[Update]

[#] [FUNC] [Preset]

[C]

[FUNC] [All] [FUNC] 
[0%]

Using Check mode from channel 1 onward:

[1] [FUNC] [100%] then [FUNC] [Check+] then [FUNC] [Check+]

At Mode
If a console is set to work in At Mode, channel selection functions on the remote behave differently. For example:

• Set channels 1 thru 5 to 55%: [1] [THRU] [5] [@Level] [5] [5]
• Set channels 11 thru 14 at full: [11] [THRU] [14] [FUNC] [100%]

Number entry after [@Level] is a two digit entry. If you only enter one number, you can press [C] to end level entry.

Oh, and regarding the training question - where are you located?

Thanks much -

Sarah

Hey Sarah,

thanks! thats just what I needed.

I'm located in Chicago....but might be able to travel depending on the dates.

Thanks again!

~Mike Lamont

Hi

We also have an Avab Lynx fader wing and I've got he same question. How long is the APN cable to connect to the Congo console at the max and is just connect the Lynx wing to the console or we have to do something more???

Hi

We also have an Avab Lynx fader wing and I've got he same question. How long is the APN cable to connect to the Congo console at the max and is just connect the Lynx wing to the console or we have to do something more???

Hi Pedro,

If your Congo console has a physical APN connector, you should be able to just connect the Lynx panel and operate it without any further actions.

The APN cable should be less than 100 m long.