• Date
    varsamis_k
  • Date
  • Replies 3 replies
  • Subscribers 67 subscribers
  • Views 2728 views
  • Users 0 members are here

Chase into a Normal Sequence

hi to all...

i am new to the forum as new i am to the programming of the console Congo.

so plz be patient with me... now my questions....

1. when i record a preset for a sequence with dynamics why the dynamics keep running even when i am to the next  preset of the sequence? (i have pressed the "auto stop dynamics" at congo setup page.)

2.i know how to create 1-2-3-4..... sequences and to load each one i want. i also know to create a chase sequence at to make a pause from WFA..... the question is  when the next preset of the sequence is like "cut" time fade, the pause is NOT working. the sequense is NOT pausing to the step i used WFA and it keep running to the next steps.... i found out that the limit of the fade in-out must be over 0.5 seconds. this is bug or is just a limit?  (Congo Ver 4.3.0)

3.is possible when i have a normal sequence that have 5 presets, to make No6 step to be a chase of 5 steps that i have create in a new chase sequense? and after that 5 steps to record again normal steps?

 example : 1-2-3-4-5 ----> normal Go steps

                    6-7-8-9-10---->Chase steps

                  11-12-13-14-15---->normal steps

coz its a bit hard to have a MainPlayback and to create a Master with Chase sequence

****************************************************************************************************************

thanks for reading and i hope to get an answer...

coz the instruction manual is hard to read and understand when

english is not the natural language for me.... :/

Parents

  • Hi varsamis

    It's been a while since V4.3.0 so I'm not sure if I it's like this but...

    1. try to put on the next preset the STOP Dynamics attributes cause for some time it's what I'm doing with that version and it always work.

    2. the pause never works with WFA times only with the preset times so if you have a WFA of 30 sec and a 0.1 sec for the next preset good luck if you can stop that preset cause I never could do that. PAUSE only goes with IN OUT and DELAY times (after you press GO).

    3.with V4.3.0 try to make a Seq. Chase and put that Seq on a master and after that just do Preset 6 with Master Link to put that chase running and Preset 7 with same Master Link to stop the chase.

    Hope that helps but like I said V4.3.0 it's been a while since that version. As soon as you can try to install the V6.3.0 and you see different things to do what you ask now. With V6.3.0 same things are more easy to do. Try it with the offline and you'll see the diferences.

     

    Pedro Alves 



    [edited by: Pedro Alves at 4:39 PM (GMT -6) on Thu, Jan 21 2010]
Reply

  • Hi varsamis

    It's been a while since V4.3.0 so I'm not sure if I it's like this but...

    1. try to put on the next preset the STOP Dynamics attributes cause for some time it's what I'm doing with that version and it always work.

    2. the pause never works with WFA times only with the preset times so if you have a WFA of 30 sec and a 0.1 sec for the next preset good luck if you can stop that preset cause I never could do that. PAUSE only goes with IN OUT and DELAY times (after you press GO).

    3.with V4.3.0 try to make a Seq. Chase and put that Seq on a master and after that just do Preset 6 with Master Link to put that chase running and Preset 7 with same Master Link to stop the chase.

    Hope that helps but like I said V4.3.0 it's been a while since that version. As soon as you can try to install the V6.3.0 and you see different things to do what you ask now. With V6.3.0 same things are more easy to do. Try it with the offline and you'll see the diferences.

     

    Pedro Alves 



    [edited by: Pedro Alves at 4:39 PM (GMT -6) on Thu, Jan 21 2010]
Children
No Data
Related

www.etcconnect.com