• Date
    John728
  • Date
  • Replies 14 replies
  • Subscribers 190 subscribers
  • Views 12662 views
  • Users 0 members are here

Contact closure adapter and remote trigger switch for I/O port

This adapter plugs in to the Remote I/O connector on the back of your Ion, Element, Gio, Gio@5, Eos, or Eos Ti console or I/O Gateway and accepts a standard 5-pin XLR control cable. (Some people would call it a "DMX" cable but in this case it isn't used to transmit DMX data.) Use it to trigger a cue, macro, or submaster remotely.

Uses

  • Allows an actor to turn any number and wattage of lights on and off using a practical wall switch
  • Put a switch next to your DP or gaffer to let him/her trigger a cue
  • Simple house lights control for the cleaning staff
  • Set up a switch next to your house light switches for easy access to kill the lights in your rig when the house lights are up
  • Gaslight anyone on the crew by building a light switch into the wall that only "works" when you want it to

Features
Allows up to 4 different cues, macros, or submasters to be run from 4 different control circuits
A SPDT switch allows one cue, macro, or submaster to be triggered from the "up" position and another to be triggered from the "down" position
Allows any number of switches to control the same cue, macro, or submaster (through the use of jumpers, not supplied)
Compatible with any 5-pin XLR cable
Compatible with any 3-pin XLR cable with use of adapters (2 control circuits only.) Does not have to be DMX-grade cable.
Compatible with a standard networking "Ethernet" cable with use of adapters.
The male end is at the console, preventing anyone from plugging a DMX line into it
Tested to work with 400' of control cable

---

 

contact closure adapter set



Edit: The original Eos doesn't have a 15-pin connector on the back.
[edited by: John728 at 4:32 PM (GMT -5) on Tue, May 30 2017]
Parents
  • No, we're on a stage with constructed sets. I can get to the plugging and wiring of practicals.
  • in reply to Wayne Simpson

    You need a relay with a 120V coil. They are pretty common and not very expensive.

    The fixture AC goes through the coil and closes the relay. The relay is just a 'dry contact' to the DB9 connector on the back of your console. Check the manual for pin-outs. A handy person could put the relay in a box with power in & out connectors of your choice and a relay out for a handy cable type (mic or DMX?) for the run to the booth. An adapter there to the console connector will make things pretty simple.

    Most of the work is just wiring so you don't need an engineer, just someone with tool skills. Best of all the whole rig is adaptable and reusable.

  • in reply to RickR

    In the case of the talent actually pulling the pull chain to turn the lamp on, a relay would have to be triggered by the flow of current to the lamp, since the v input would already be present, right? Another caveat is that I'll need the relay solenoid to engage under a wide range of voltages, for instance, if I'm running the practical at 12%, which happens. Electronics tinkerer friend suggests modifying the guts of an Amprobe to trigger a relay. He also suggested an on-set optical trigger cued to the light emitted by the practical, but that seems dicey in practice. I suppose it would be possible to make several of these for different voltage ranges, swap it out quickly if the input voltage dropped below a certain range.

  • in reply to Wayne Simpson
    Yes, it's the amperage that triggers the relay, not the voltage. You will need to define a minimum voltage to design the system around. Also a maximum amperage the unit can handle without burning up. That's where an amprobe comes in handy. An optical sensor will always give you a delay in triggering, and you already have some due to processing and signal travel.

    An independent switch like John mentions is always preferred, but not always practical. Though a touch sensitive trigger could easily be attached to anything metal. I've got some in built in furniture lights and attached to the door hinge. I've never tried it, just came to mind while writing this!
Reply
  • in reply to Wayne Simpson
    Yes, it's the amperage that triggers the relay, not the voltage. You will need to define a minimum voltage to design the system around. Also a maximum amperage the unit can handle without burning up. That's where an amprobe comes in handy. An optical sensor will always give you a delay in triggering, and you already have some due to processing and signal travel.

    An independent switch like John mentions is always preferred, but not always practical. Though a touch sensitive trigger could easily be attached to anything metal. I've got some in built in furniture lights and attached to the door hinge. I've never tried it, just came to mind while writing this!
Children
Related

www.etcconnect.com