New versions in progress ?

And I will add:
Some memories, with effects are impossible to change. The effects generator seems completely disturbed by any modification. And not work anymore, you have to clear, to reset ...but sometime no way...
There are memories that do not memorize properly including and I noticed that it is with the blue color under a weak intensity, that it is quite unstable.
You do not imagine the loss of time that it generates.

I never had this before this 2.5 version. 

More comments: Could you give us an example where effects cannot be edited? We need to be able to reproduce this here to be able to fix it.

Memories not memorizing: Is this about colors when you have used direct emitter colors? We have just fixed a problem in v2.6 where direct emitter colors misbehave, especially on low colors.

It is difficult to explain, In some Cue, I have an effect color and sometime an intensity effect, this on eight device.

If I have to modify one position (pan tilt) from one device, the effect on this device is brocken. And the problem, is that, in this case, it is impossible create again the same effect one this cue, without to reset, to clear color....

I can send you the project and give you the cue Nr.

Memories not memorizing : good news if you detect the problem.

Here is the show

https://1drv.ms/u/s!AgAT9FIDC1tIjfBrU8Zj4cCV9idKOA

Step15 :if we modify a device (pan tilt) of this sequence the effect is broken.

step 26: normally the channel 28 should be blue at 8% and 30 at 8% white. I had difficulties memorizing this scene, it was never reproduced as planned.

Step 72: Normally channel 27,28,29,30,38,39 have an color effect "primary" .But the channel 30  does not have the same intensity. Impossible to change without breaking everything.

On the 

Step 69.1 : Try to replace this poor effect (which is not the one planned) with a effect color FLAG on 27 to 30 and 73 to 40 and see !

All these recording examples seems to work for me and our tester. Are you using "Update Live Cue"?

(recording of memories on low levels of direct emitter data is a separate problem that is fixed in v2.6)

Do you make you test with a real console, or with the off line software ?

Because with the software, it seems working, but not on a real console.

NO ! Anders, it's not possible you do not see anything, I can not believe that !!! 

I just try to load it on the CS simulator, and for exemple, on  the Step 72 the channel 30 doesn't have the same intensity , WHY ? and how modify it , TRY ! IT IS NOT POSSiBLE.

And on the same way , all Effects are complicated to edit.

NO ! Anders, it's not possible you do not see anything, I can not believe that !!! 

I just try to load it on the CS simulator, and for exemple, on  the Step 72 the channel 30 doesn't have the same intensity , WHY ? and how modify it , TRY ! IT IS NOT POSSiBLE.

And on the same way , all Effects are complicated to edit.

There is a problem in v2.5 with low intensities of direct emitter data that we have talked about separately. This is fixed in v2.6. Running with v2.6, I can fix the intensity and use Update Live Cue to re-record it. After that, it will play back correctly. So this specific problem is already fixed with v2.6.  

Ok thanks Anders, I understood the problem of low intensities, but in the example, the whole effect was at full, but only one channel (30) is weaker.  I would like to be sure that you have correctly identified the problem.

if I understand well, I have to wait on the v2.6 .

I think that the level of channel 30 was recorded on a lower level due to the problem with lower intensities and direct emitter values in v2.5. Once I re-record it with a higher level with v2.6, it seems to play back correctly from cue 72. So yes, I think that v2.6 will solve this problem.
If you are willing to verify this with a beta version before we make the official release, that would be good.

Ok, yes of course ,when the beta version will be available.