Connecting ion to wysiwyg r29

Hi,

I have my ion and r29 all set up and i am able to ping the console from computer.

Wysiwyg in live mode says receiving EDMX / No connected devices.

I have Net2 enabled and all my IP addresses appear to be working fine.

Anyone have any knowledge to what i may be doing wrong or why this is not working.

Thanks

0 sk8rs_dad over 12 years ago

You may find a clue in the wiki:

http://community.etcconnect.com/wikis/products/knowledgebase-connecting-congo-and-eos-family-consoles-to-a-visualiser.aspx

You may be bumping up against firewall issues, and some routers will suppress multicast packets.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Ntrapani over 12 years ago in reply to sk8rs_dad

Have been to the link supplied before and done all that it suggests. Still no change in results.

Going to try bypassing router. If that does not still work any more suggestions?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 ueliriegg over 12 years ago in reply to Ntrapani

have u checked, that you're outputting the right protocols (in the shell) and that in patch you have these protocols toggled on for all channels you want to have visualised?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 nelakluwos over 12 years ago

Have you patched your fixtures into the EDMX universe? When you are in Data mode under the Patch tab, do you see any DMX values?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Staatstheater82255 over 12 years ago

... I have nearly the same Problem:

I'm trying to conect a laptop (running in offline mode 1.9.12.9.0.1) to a wysiwyg R28 Installation on my PC. Both operating systems are windows7.

Wysiwyg settings:
allow EDMX reception v4
Recieving EDMX / No connected device in live view

EOS offline settings:
ACN=1, EDMX=20
IP: 0.0.0.0
IP: 0.0.0.0
IP: 192.168.123.223 (via the DHCP server)

All chanels are patched on the "standard" interface (ACN EDMX DMX)

I tried to do everything that is describet here (http://www.cast-soft.com/wysiwyg/tip/view/connecting-to-edmx-networks), there (http://community.etcconnect.com/forums/t/10628.aspx) and there (http://community.etcconnect.com/wikis/products/knowledgebase-connecting-congo-and-eos-family-consoles-to-a-visualiser.aspx) - with no sucsess.

I would to find out, wether the PC (with wysiwyg) is recieving EDMX signals, but I don't know how. Maybe with Net2Util (how do I get this)...

Thanks for any help!
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 ueliriegg over 12 years ago in reply to Staatstheater82255

did you switch on the output in the shell of the offline editor? shell > Network. choose the protocols and below that, you have to check the box for output in offline mode.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 luke.delwiche over 12 years ago in reply to Staatstheater82255

You might be best off calling your local support - they should be able to help and provide Net2Util if needed.

Luke
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 tomdavislx over 12 years ago

Try following this guide, the problem I had with it was solved when I followed the instruction to run the AppMux application (Casts EDMX listening application) as an administrator.

http://www.paintingwithlight.be/downloads/WYSIWYG.DOWNLOAD/TipsTricks/ThePlan-TipsNTricks-Issue36.pdf
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel