Howdy...
How is accesses? Firmware 3.11
Thanks!
I was awaiting someone from ETC to chime in....
To my knowledge, there is no built in access to any kind of diagnostics or to the firmware.
The console series (Expression/Insight/Express) did not have hard drives. The OS booted from 3.5" floppy when installed and the OS then ran in bios.
What exactly do you need to do, and can I assume trouble shoot a problem ?.
Steve B.
just picked up a console used and wanted to run whatever tests built in I could to ensure it's in good working condition. I'm surprised there isn't a function available to do this. What's the "reserved" #12 in the setup then believe it's option's menu?
There must be a way for it to run a system's check? no?
There are no 'built in' self-tests for the Expression line but generally speaking you should be able to use the console to see if everything is basically working. If it boots and you end up in the Stage screen then you are 90% there. Run though all the buttons and sliders to make sure they are actuating and then ensure you are outputting DMX. ETC Link and RFU testing would require a Link device and a RFU. Save a show to disk and then load a show from disk.
'Reserved' #12 in the Setup is not anything :-)
You can clear the unit back to all defaults (this will erase the show and patch) by doing a 789 Deep Clear. With the console turned off....hold down the 789 keys and then turn the console on (continue to hold down 789 until the unit is done booting
If upon System Reset, the following message appears: Record is locked out. Press Clear to continue.
Cause Record Lockout is enabled in the System Settings menu in Setup.
To disable:
[Setup] [1] [Enter] [13] [Enter] [0] [Enter]
You might hear rumors of an Expression Diagnostics test but this is a software tool used by ETC and our Authorized Service Providers to test for specific failures on a unit that has a reported failure from an end-user.
Sincerely,
Mike
Also,
If you are new to the Expression line or run into some odd questions, please also see the WIKI page for Expression: http://community.etcconnect.com/wikis/products/expression-insight-consoles.aspx
I'm always pushing the WIKI :-)
There is a long list at the bottom of the article but you can run a search of the complete ETC WIKI.
Thanks for the deep clear tip - no I'm not new to the console at all... I've got four of them running in our facility right now. Just wanted to do a more thourough test and run through than simply loading one of my existing shows and hoping everything works.
Now lets get back to that "reserved 12" item.... what is it for and what does it do.
thanks.
Reserved 12 goes nowhere and does nothing - it's a placeholder in case we needed to add something to the menu.
It turns out that we didn't need to.
how about a diagnostic function.. that would be convenient to add in there, wouldnt it? Lock it out similar to the CEM module's login?
Console is long out of manufacture, so don't plan on it.
SB
so how about making the diagnostic tool downloadable for people to use since the console is too old, out of production, and no longer supported? not an unreasonable request by any means.
so how about making the diagnostic tool downloadable for people to use since the console is too old, out of production, and no longer supported? not an unreasonable request by any means.
I wouldn't go so far as to say that it's unsupported. ETC still supports L86 dimmer racks which they actually never made - they just acquired the company that made them before they came out with the sensor rack.
Being that the console is out of production, I doubt that any more R&D dollars are going to be spent on getting a diagnostic tool out to the end users. As Mike said before, there's really not that much to the console that you couldn't spend about 10 minutes and do a pretty full diagnostic yourself.
who said they needed to create a diagnostic tool? It already exists... simply load it in the download section of the website so console owners can make make their own floppy disks with the tool on it and check their units for correct operation...
again... not much to ask.
b_valkyrie said:so how about making the diagnostic tool downloadable for people to use since the console is too old, out of production, and no longer supported? not an unreasonable request by any means.
The console is still supported, but your request was to add in a diagnostic tool, into the operating system software, for a console that is no longer manufactured. I would suspect that this is not going to happen and quite frankly ETC tech has other things to do besides adding software to the OS to a 20 year old computer.
Your request to make the diagnostic tools available as a separate piece of software makes sense.
SB
Actually my initial request was NOT to "add" a diagnostic tool, but instead to simply access the prexeisting tool. As was demonstrated in this topic, the tool does exist however it's not installed resident on the console and instead needs to be loaded separately... so then again I ask politely if this diagnotsic tool can be made available for download for all of us Expression owners who want to perform periodic routine checks on our units.
sound of crickets chirping from ETC as diagnostic tool does not yet appear in download section of site.
Hi there -
We are considering your request. We cannot simply post a 15-year-old diagnostic software tool on our web site since it was never designed for use by anyone other than manufacturing and repairs techs. There's no documentation, no instruction sheet, and very little user interface on it and we need to make sure that all that is in order before we post something like that. Please stay tuned...
In the mean time, here are some old-school tricks to use to test your console:
1) Use the HELP key. I know it sounds a bit odd. but before the diagnositc tool existed we used the HELP key to test that all the keys were working. Pressing HELP and any other key should provide a message - if the message appears and it's the right one for that key, then the key is working.
2) Use the Submaster List view and the playback areas on screen to test the faders. You should see the % level of each fader as you move them. For the Grand Master, you can see its level on screen as well. All faders should fade smoothly from 0-100, as I expect you know.
3) Test the quality of the keys using the triple-hit method. Press each key three times quickly in rapid succession. You''ll quickly get a feel for how good keys react and sound. When/if you hit one that's marginal, it will feel "softer" or "deader" and will sound dead as well - not CLICK-CLICK-CLICK rather CLACK-CLACK-CLACK as you go.
4) Testing outputs/Inputs is going to require other gear than the facepanel diagnostic we may provide - a DMX Tester for the DMX outputs and input, MIDI equipment for MIDI stuff. I cannot remember if the diagnostic tool has any loopback tests in it at all, in which case you would only need cables. We will have to wait for Tech Service to provide that information once they look into the feasibility of letting the tool loose into the wild.
Thanks much -
Sarah
Sarah,
This is a little off topic, but does the sales department still sell the Expression 3 manual?
Thnx!!!!
-Lightingguy1
Hi there -
Contact tech support or customer service. If we have any, I'm sure we'd be happy to sell one. Or, it is available free on the Web site as a PDF download as well.
Thanks -
Sarah
After spending a bit of time with the diagnostic tool it seems like it is far from the best thing to make available to the public. Please follow me on this. I was thinking on Sunday that this would be ok to post but I hadn't looked at it in over 10 years.
There is a semi-useful facepanel test that allows you to check and see if buttons and faders are working. There is also a DRAM and SRAM test but they can erase your OS as well. There are no instructions, no guides or menus, you have to know how to run it and it really does not diagnose much. If you wanted to check CPU temps, bus speed, clocking, parallel port functions, disk drive access, etc, there just isn't anything in the diag disk.
I get the question from time to time stating that there must be a diag box at ETC for each piece of gear that we hook up to that tells us what's wrong with stuff. Truth is, no, we just have a really smart repair department and a lot of good folks on the phone. Maybe it would be cheaper to do this in the products, and we have added more stuff ito the newer products over time, but some of the older gear just doesn't have that level built in.
I hope you understand,
David
There is a quick easy way to test to see if your console is running in good shape. This is a test repairs does.
1) Create a Macro with the following commands:
<Live> <Blind> <Patch> <Setup> <M_>
The <M_> is the macro number your creating. This macro will switch displays on the desk and run continuously until you hit M*.
2) Create a subroutine of a couple of cues.
3) Run the subroutine on a playback, then run the macro.
What this does is put a heavy load on the desk. You will know pretty quickly if the desk is in good working order. I usually run this test for about 10 minutes.
Hope this helps
P-
Actually I don't entirely understand... The console itself isn't exactly the easiest to use so I don't think any of us would expect the diagnostic tool to be either.
I'm sure you have a PDF with notes or commands on how to use it, or there would be someone here willing to create one if you dont already (though I doubt that one does not exist).... Why not make it available for download, bundle it in a zip file with the instructions and if you are really concerned ask for the console serial # to log when people download it.
I dont think anyone is questioning the ability or the competency of the ETC support department - they've been fantastic (at least in my experience) however given the frequency that some of us use this console and the many many odd hours we work having the diagnostic tool handy would be an asset in operation and troubleshooting. I can think of five specific occasions in the last 4 months alone that having that tool at my disposal would have ended more than one disagreement over hardware failure vs human error (and it's always human error)
I'm sure there is some way you can make this available for those that need it and still keep it out of the hands of those that shouldnt use it.
"I'm sure there is some way you can make this available for those that need it and still keep it out of the hands of those that shouldnt use it."
It seems to me that they have already done so by limiting it's distribution to those properly trained in it's operation and use: Factory Trained Technicians.
How much time and resource should ETC commit to writing/compiling documentation for a piece of software that was never intended for public release? I, for one, would much rather they continue to focus their energies on new product development; software and hardware. We all know ETC will continue to service and support their products to an extent that very few other manufacturers are even willing to consider; should your console ever actually develop a problem I have no doubt you will be well taken care of.
Best,
John
(Who doesn't work for, or speak for, ETC (nor anyone but himself); but is a longtime, very satisfied, user.)
how much time? none... they have already stated it exists and can simply be placed for download. And I disagree with you 100%. It is unfair to expect an owner of an unsupported 10 year old console well out of warranty to have no way to confirm if their unit works correctly or does not without taking it in for service every time. That's ludicrous. A basic systems check should be free.
b_valkyrie said:It is unfair to expect an owner of an unsupported 10 year old console well out of warranty to have no way to confirm if their unit works correctly or does not without taking it in for service every time.
It is rather fair to expect that. It is a 10 year old product that is also out of warranty (and when you say unsupported I'm not sure what you entirely mean). I highly doubt that if you called ETC Tech Support and asked a question about an Expression, they would deny you any kind of help and say they don't support the product anymore. ETC is probably the ONLY company that I can say I feel 100% comfortable calling and receiving quality help on legacy equipment.
b_valkyrie said:A basic systems check should be free.
A basic systems check is free, did you read the earlier posts with suggestions on how to perfom you own basic systems check?
What are you looking to test anyway that you can't by doing what has been described in the previous posts?
I think at this point what I'm reading is whining. Dave North, one of the senior and most experienced engineers at ETC has pretty much indicated - nicely, that the diagnostic software is not going to be released to the public, for a lot of good reasons, including the fact that it was never intended for non-ETC technicians to use and that there's the potential for screwing up your console in such a manner that it would take ETC Tech Support longer to tell you how to fix then it's worth.
And as BTW, most of us who've been in the business as long as we have, have learned to listen when "DNorth" speaks, sort of like EF Hutton. I'd take the advice.
Note that I have followed the ETC forum since the beginning and this is the only request I've ever seen to use any kind of diagnostic on a discontinued (but still supported) product that is 20 years old. Call HP and ask for similar support, they'll go "Huh" ?. I'm certain that a lot of computer manufacturers have diagnostic tools intended for factory use that they will never release to the public. Same thing here.
Most folks trust ETC Tech Support to tell us when a product is functioning correctly or not, and I've seen a lot of posts here describing exactly that for your situation. I would think that would be sufficient as the console simply isn't so complicated that the tests others have suggested are not going to tell you what you want to know.
And not for nothing, but everyone of these ETC folks have better things to do then deal with this, there are certainly folks calling with more pressing issues, so can we close this out now ?.
Steve B.
www.etcconnect.com