iRFR channel check mode??? for iPhone app

The RFR will now boot into channel check mode - this was changed in 1.9.5.  To get to live mode, hold down the upper left button and select "live" on the appropriate softkey.

-Todd

I for one, wish it would boot into LIVE mode instead of channel check mode.  There doesn't seem to be a sneak or out option when in channel check mode, so I keep mistakingly bring up a channel manually and have to switch to LIVE mode to take it out.

In my original reply, I missed the "i" part in "iRFR"- so I described the behavior of the dedicated RFR unit.  I'm not sure if the iRFR does the same thing...

JP- on the RFR in channel check mode, pressing [clear] should take out the channel as well as clearing the command line.  If it doesn't then there's something strange happening.

-Todd

I realized that it was a small "i" so I edited.  But anyway thanks for the quick reply.

Todd, yes clear works when in actual channel check mode, but if you actually type in "1atFULL ENTER" it captures that channel at full.  The only way to take it out is either to set it at 0 or switch to LIVE mode and sneak or out it.

jpgagnon said:

Todd, yes clear works when in actual channel check mode, but if you actually type in "1atFULL ENTER" it captures that channel at full.  The only way to take it out is either to set it at 0 or switch to LIVE mode and sneak or out it.

JP- on my RFR if I type "1 @ FULL ENTER" in channel check mode the RFR command line reads:

• 1 @ FULL CHECK *

If I press CLEAR, the command line is cleared and the channel goes out.

I would give ETC a call- perhaps its a RFR firmware or configuration issue.

-Todd

I totally agree!  The majority of the time I am using my iRFR it is in LIVE mode.  I would much rather switch it manually to Channel Check when needed.  Thoughts??

Travis Shupe

Harpo Studios

I feel the same way Travis. I do not like it defaulting to channel check mode.

I also agree that iRFR should boot up in LIVE mode...

That's what I use it for almost 100% of the time. Perhaps add a setting to choose which mode you'd prefer to boot in?

I, for the record, like the fact that it boots up in channel check mode. Most times when I'm using the iRFR software, I'm either patching or checking a rig. (And I believe this is ETC's intention for the remote)

However, RFR stands for Radio Focus Remote. . .   so focusing would seem to be the intent.

I too would prefer the iphone remote to boot up in live as I find I have to keep switching modes whenever contact is lost with the desk.

Ian

Personally, it seems like it should come back up in the mode that it was in last.

-Steve

If we're all putting in our opinions for what mode we like to boot in, I prefer the new channel check mode.

Maybe it could be a user setting?

My apologies about my previous statement about 1@FULL ENTER.  Yes, that puts it into channel check, but if you type 1 FULL FULL(which is much quicker) it does not add the CHAN CHECK at the end of the command, so then that channel is captured(sorry, old expression term) and the only way to un-capture it is to switch to LIVE MODE and OUT or SNEAK it.  I would like an option on the chan check page for a softkey for OUT or SNEAK.  Or of course, just default to LIVE MODE (I like the idea of a preference for this default).

My apologies about my previous statement about 1@FULL ENTER.  Yes, that puts it into channel check, but if you type 1 FULL FULL(which is much quicker) it does not add the CHAN CHECK at the end of the command, so then that channel is captured(sorry, old expression term) and the only way to un-capture it is to switch to LIVE MODE and OUT or SNEAK it.  I would like an option on the chan check page for a softkey for OUT or SNEAK.  Or of course, just default to LIVE MODE (I like the idea of a preference for this default).

Thanks all for your input  JP, we agree with both of your comments.  

:-)

a