can not update full boar

I bought a Road Hog 3 Full boar last week.

During the show it got stuck and could only operate the faders.

I just found out that version 3.2.1 has been installed.

The full board is equipped with a new ssd, but I am unable to update it to version 3.2.6 b3434

I have burned several CDs with deepburner and used 2 usb.

the full board sees the usb and cd roms but not the fpspkg file.

Which is why I am unable to update.

who can help me or has a solution?

Top Replies

Gabbi over 1 year ago in reply to ulrichr +1

Section 31.4 has instructions on how to perform installs, please click here The last Hog 3 software version can be found here: v3.2.6 (B3434)

0 ETC Kyle Kurtich over 2 years ago

Try using the Hog 3 PC msi file to perform the update via USB. That has been known to work on Road Hog 3s and Road Hog 3 Full Boars.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 ulrichr over 1 year ago in reply to ETC Kyle Kurtich

and that is done how ? i mean how to make the console open the msi-file ?

sorry, but i'm new to the HOG 3 / Full Boar. I just noticed that it uses Windows features for a restore.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Gabbi over 1 year ago in reply to ulrichr

Section 31.4 has instructions on how to perform installs, please click here

The last Hog 3 software version can be found here: v3.2.6 (B3434)
Cancel
Vote Up +1 Vote Down

Sign in to reply

Verify Answer

Cancel
0 ulrichr over 1 year ago in reply to Gabbi

thx Gabbi

unfortunately the steps from the manual get me to the attached screenshot with nowhere to go.

there's to say that I got the console in this state and with a dead bios battery. the latter I've fixed so both screens work again. If i don't choose a full restore the console stalls waiting for the front panel to communicate. a forked way with 2 dead endings for the moment.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 ulrichr over 1 year ago in reply to ETC Kyle Kurtich

ETC Kyle Kurtich

how am i supposed to have the console handle the MSI file ?
As far as I can tell the manual doesn't cover that part in chapter 31.4 ff

thx
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 ETC Kyle Kurtich over 1 year ago in reply to ulrichr
Download the Hog 3 PC software for the version you wish to install on your console.

Connect a USB stick to your computer

Take the MSI file out of the zip folder and place it on your USB stick

Connect the USB stick to your console

On the Hog Start window, press Update Software

Select the MSI file on the USB stick

I ran it one time and it popped up a message. I re-ran the install and I had a successful installation.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 ulrichr over 1 year ago in reply to ETC Kyle Kurtich

ETC Kyle Kurtich

hi.

thx for your reply and the detailed steps to take.

unfortunately none of the above works. a Full Restore while booting from USB stalls at the the point of which i took a screenshot with no option to select a different file, drive etc.

selecting a file from the Hog Start window as you suggested in step 5. isn't possible as the console doesn't even get that far booting.

Holding the Pig-key while booting doesn't work either as the front panel seems to be not being detected

I've figured that the front panel was connected to the wrong port at the time of purchasing the console and I corrected that 'glitch'. Also the bios battery was drained and I replaced it.

As of now the touch screens, while being routed usb-wise through the front panel, work and the panel gets power from the PSU as indicated by some leds of which I removed the foil that blackened them out..

By now I'm about to look for a working front panel while checking the one i have for whatever issue i might comer across.

thx again
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel